Measure the Garage Before You Buy the SUV

- PublishedNov 19, 2026
- Sources2
- 11 min read
Measure the true garage opening, check mirror width and liftgate travel, and test everyday access before buying an SUV.
Decide First
Ford's technical specifications for the 2025 Explorer list three different widths for the same SUV. With the mirrors excluded, it measures 78.9 inches wide. Fold the mirrors and the listed width is 82.7 inches. With the mirrors extended, it is 89.3 inches. All three figures are correct. Only one describes the shape of the vehicle as you normally drive it through a garage door. Ford's 2025 Explorer technical specifications, exterior dimensions
That makes “will it fit?” three different questions. Can you enter without scraping anything? Can you get out and close the garage door afterward? Can you open the liftgate and use the space on an ordinary day? An SUV can pass the first question and fail the other two.
Open the garage door fully. Measure clear space between the pieces that project into the path, including the trim, track hardware and weather seals. An eight-foot door description gives you the nominal size. Use your measured opening for the fit decision.
Take a width measurement around mirror height and look at whether the opening narrows elsewhere. Do the same for height at the lowest point across the route. A door that does not rise all the way, a low crossbeam and an opener assembly can each create a different high point to avoid. Keep the measuring tape out of the door's travel path and leave the door stationary while measuring.
Set aside the number from wall to wall for now. An interior dimension matters once you've entered. It cannot make a narrow opening wider.
Suppose your clear opening measures 90 inches. This is an illustration using Ford's published Explorer dimensions, not a recommendation to drive through that opening.
| Mirror configuration in the Ford specification | Listed vehicle width | Width left in a 90-inch opening |
|---|---|---|
| Mirrors excluded |
Comments are shopper discussion, not verified article evidence.
Comments are not open on AutoUnite yet. Published articles and Ask AutoUnite are the current way to get answers.
AutoUnite content is educational and research-focused. Vehicle information, pricing, ownership costs, maintenance, recalls, and other details may vary by region, dealer, and time.
| Listed vehicle width78.9 in |
| Width left in a 90-inch opening11.1 in |
| Mirror configuration in the Ford specificationMirrors folded | Listed vehicle width82.7 in | Width left in a 90-inch opening7.3 in |
|---|
| Mirror configuration in the Ford specificationMirrors extended | Listed vehicle width89.3 in | Width left in a 90-inch opening0.7 in |
|---|
If an 89.3-inch vehicle were centered in a perfectly straight 90-inch opening, the arithmetic leaves 0.35 inches per side. That assumes the vehicle is square to the opening and perfectly centered. It leaves almost no room for a small steering correction. The much larger 11.1-inch figure uses a measurement that excludes the objects most likely to brush the trim.
The folded measurement gives a different answer, but decide whether you want to build your daily parking routine around folding the mirrors. Does the exact vehicle have power-folding mirrors? Can you fold and unfold them from the seat before entering and after backing out? Will a family member who parks the car also be able to do it comfortably? Test the actual controls while parked with permission. Verify equipment on the exact vehicle.
There is no single margin in this example that makes another garage or another vehicle safe. If the numbers come down to a very small clearance, ask for a fit check or choose a narrower candidate. Never use the vehicle itself as a measuring tool by attempting a tight entry.
Picture a townhouse garage you reach by turning around a column. You can take the same opening measurements you would take at the end of a straight driveway, but the car may cross the threshold while still turning. As it does, different parts of the body and mirrors pass different points on the opening. A simple subtraction tells you the unused width in a straight, centered setup. It leaves out the turn, the column and how much room you have to straighten before the garage.
Walk the route before anybody moves a car. Mark the direction you would approach it and the points that keep you from lining up in advance. Check the other end of the trip as well. A car that can be driven in with room to straighten might be harder to get back out when a second car is parked behind it. Measure at the garage entrance with normal obstructions in place. If reaching the opening requires a maneuver you cannot verify comfortably, leave that item open when you compare cars. Ask about the dealer's options for a fit evaluation before agreeing to buy.
Sloped approaches deserve their own sketch. The part of the floor just outside the opening matters because the vehicle might be angled upward or downward when its roof crosses the header. An accessory that sits toward the rear can cross that spot at a different angle from the middle of the roof. Confirm clearance through the actual passage with the intended equipment. Putting the flat-ground height in the spreadsheet is a starting point.
Map the usable depth from the inside face of the closed garage door to the closest obstruction in the parking position. Shelves, a workbench, a curb stop and the location of a charging cable can all matter. A depth measurement to the drywall is useful only if the vehicle can actually occupy that space.
Now think about what changes after the wheels stop.
Driver access. A parking spot may be wide enough for the SUV and too narrow for you to open its door. If you park next to another vehicle, check the space with both present. Think about who opens a rear door, how often someone loads a child seat and whether a passenger can safely get out before the vehicle enters if necessary. Confirm that the driver's door works for the person who will use it every day.
The rear hatch. The published vehicle height describes the vehicle in the configuration stated in its specification. Ask the seller to demonstrate the liftgate and, if equipped, any opening-height limit. Ford's instructions for the 2025 Explorer equipped with the hands-free liftgate describe setting a programmed opening height on that system. Even with a limit in place, the path to the programmed position still has to clear the walls, rails and open garage door wherever you park. If you cannot verify that path, keep the hatch closed inside and decide where loading would happen. Ford's 2025 Explorer liftgate instructions
Accessories and operating position. Write down what stays on the vehicle, including roof crossbars or a cargo box, and ask for the installed height. There's no need to subtract accessory dimensions from a marketing rendering. Get the height in the configuration you intend to park. Check both the opening and any lower point beyond it, especially if your driveway slopes sharply into the garage.
If you rely on a garage EV charging setup, include the location of the charge port and your normal parking direction in the fit check. A vehicle that fits nose-in may put the port on the far side of the garage from the cable. That is a reason to map the parking layout before buying, rather than assuming that the cable will reach across a walkway.
Take a household with two drivers, a folding stroller and a second vehicle in the next bay. Moving the second car to get the stroller out could seem fine on a Saturday with the dealer. On a wet morning with both cars home, the same workaround might make that vehicle a poor choice. A representative fit check has the second car parked where it normally sits and leaves the shelves where you intend to keep them. It also includes the driver who needs more room at the door. The point is to learn how the space works once the test ends and the car belongs to you.
Start with the access you use most often. A driver with a cane, a rear-facing child seat or a large work bag may need more door travel than the person who takes the test drive. If you load a bicycle or a wheelchair through the back, check the path around the car, not just whether the hatch can reach a programmed position. Check the place you stand behind it. The rear bumper can be in the clear while the space for loading is too tight.
Some households can change the garage instead of the car. A shelving unit that can move easily is a different decision from a structural post, a shared path or a garage door track. Write down any changes the purchase assumes. You may discover that you are comparing an SUV you can park the day you bring it home with a second SUV that requires moving storage and deciding who parks where. Both can be viable choices. Price the change and decide who will do it before you call the fit issue solved.
An email that asks “is it the same size as my old SUV?” leaves the seller guessing. Give them the model year, trim and equipment you are considering, plus three or four dimensions that matter. For a vehicle on the lot, ask to see the exact one and look at the roof accessories, mirror controls and liftgate in person. If you're comparing listings from several dealers, use AutoUnite's exact-trim comparison guide to make sure every specification describes the vehicle you've shortlisted.
A useful note to the dealer includes the following measurements and constraints.
If you arrange a vehicle fit check, agree on where and how it will be done. Stop if any part of the approach or clearance is uncertain. You can test other everyday functions during a purposeful test drive, but the geometry of your garage has to come from your garage.
Suppose two crossovers both clear your measured doorway on paper. For the first car, the listing gives a body width and says the mirrors fold. You still need the mirror-to-mirror measurement in the configuration you expect to use. For the second car, the dealer can show an appropriate width and demonstrate the liftgate on the exact model. It leaves you with one question about the shelf behind the car. That is a manageable comparison. You know which follow-up could change the answer in each case.
Keep the measurement and its source together. If a dealer measures a car, ask whether it has the same rails, roof accessories and mirror style as the one you would buy. A walkaround of an in-stock example can be useful when all those points match. Write down differences if you are ordering different equipment. Get the exact published specification where you can, and label measurements you made yourself so another person can repeat them.
When comparing fit results, distinguish an observed demonstration from an estimate. “We folded the mirrors while stationary and measured 82.7 inches in this configuration” tells you exactly what was measured. “It will fit if you fold the mirrors” also assumes a particular opening and approach. Write those assumptions next to the figure. If you are taking measurements on different days, keep the same reference points for the car and garage.
If the fit is essential and you cannot verify the configuration before signing, ask how the agreement handles that condition. Read any terms before paying a deposit. The useful result of this check can be a smaller vehicle, a rearranged garage, or confidence in the original choice. What matters is gaining that confidence while you can still make a choice.
Only if the numbers you're comparing include the parts that matter at the tightest point. For an ordinary drive through an opening, get the width with the mirrors extended. If folded mirrors will be part of your routine, measure against the folded specification separately.
No. Ask what the exact vehicle supports and verify the hatch's travel in a clear space first. The sweep of the hatch and the position of an obstruction can matter before the gate reaches its highest point.
Your current car can help you identify the obstacles and the parking position you use. Its dimensions are not a substitute for direct measurements of the new vehicle, especially when the mirrors, doors and liftgate move differently.
What matters. You need space to enter, park and use the vehicle, with your real accessories and the garage set up as you normally use it.
Watch this. An inviting body-width figure can leave out the mirrors. The height figure can leave out the open liftgate.
Your next move. Put your clear opening and usable interior measurements beside the exact vehicle's specifications. Mark each of the three questions as proven, failed or still open before you commit.